All existing expansion or movement joints should be followed through the new floor surface. Joint sealant & joint geometry should be compatible with the floor type used, intended exposure conditions and likely movement characteristics of the substrate.
1. MCON 3K EPOXY FLOOR TOPCOAT flooring is supplied in four pre-weighed packs (base, hardener, aggregate and colour pack) which are ready for immediate on-site use. Part mixing of these components is not acceptable and will affect both performance and appearance of the finished floor.
2. Mixing should be carried out using slow speed power mixer.
3. The colour pack should be added to the base container and mixed for 15-30 seconds, until homogeneous. Then add the hardener and mix for further 30 seconds, until an even colour and texture is obtained. Thereafter, the contents of the graded aggregate pack should be slowly added and mixing carried out for a further 3 minutes until a completely homogenous material is obtained.
1. Easy to apply. Flowable, Minimize down time.
2. Excellent resistance to wide range of chemicals
3. Excellent abrasion resistance.
4. Provides a dense, impervious seamless floor surface which can be easily clean
5. Available in wide range of colours to enhance the working environment.
1. The material should be poured onto the prepared and primed substrate as soon as mixing is complete. It should be spread to the required thickness using a serrated trowel; with care taken not to overwork the resin, spreading evenly and slowly.
2. Immediately after laying, the material should be rolled, using a spiked nylon roller, to remove slight trowel marks, and to assist air release. The rolling should be carried out using a ‘back and forth’ technique along the same path.
3. An overlap of 50% with adjacent paths is recommended. Further light rolling may be required to remove surface imperfections, or for subsequent release of trapped air, but should be prior to the setting of the product.
1. All surfaces treated with MCON 3K EPOXY FLOOR TOPCOAT should be primed with MCON 2K EPOXY PRIMER (mixed as per instruction) a solvent based epoxy resin primer should be applied immediately to the prepared substrate using stiff brushes and/or rollers.
2. The primer should be well ‘scrubbed’ into the substrate to ensure full coverage; care should be taken to avoid over application. Allow the primer to dry completely before applying any underlay or topcoat flooring.
1. Skin contact : Immediately wash thoroughly with soap and water.
2. Inhalation : Remove to open air. Seek medical attention.
3. Contact with eyes: Immediately wash under running water with eyelids open for at least15 minutes. Seek medical attention.
4. Ingestion: Rinse mouth thoroughly and drink plenty of water. Seek medical attention.
MCON 3K EPOXY FLOOR TOPCOAT has a shelf life of 12 months if kept in warehouse conditions at 30 C in the original, unopened pack.
MCON 3K EPOXY FLOOR TOPCOAT is designed for application at a nominal thickness of 3 mm. Substrates should be dry and not suffer, or be likely to suffer, from rising damp. If necessary, suitable damp-proof membranes should be installed to prevent this.
It is essential that MCON 3K EPOXY FLOOR TOPCOAT is applied to sound, clean and dry surfaces in order that maximum bond strength is achieved between the substrate and the flooring system. All dust and debris should be removed prior to application of the product or its primer.
New concrete, or cementitious substrates, should be at least 28 days old and have a moisture content not exceeding 5%. Laitance deposits on new concrete are best removed by light grit blasting, mechanical scabbling or grinding.
Existing concrete floors which require refurbishment must be prepared to ensure a strong adhesive bond between the flooring system and the existing floor. Mechanical cleaning methods are strongly recommended particularly where heavy contamination by oil and grease has occured or existing coatings are present. To ensure adhesion, all contamination should be removed. Proprietary chemical degreaser may be used on small areas of light contamination only.
1. MCON 3K EPOXY FLOOR TOPCOAT is recommended for use in a wide range of light to medium industrial environments areas where lasting solution to floor maintenance. It is ideally suited for following industries.
2. Clean rooms
3. Laboratories
4. Plant rooms
5. Light industrial plants
MCON 3K EPOXY FLOOR TOPCOAT is three component pigment epoxy based self-leveling flooring consisting of base, hardener and quartz fillers, when laid on the floor it provides a smooth, levelled and light reflective surface.
Coverage: 0.25 m2/kg @5mm thickness
Packing:
1. PART – A 5 Kg HDPE PAILS
2. PART – B 2.5 Kg HDPE PAILS
3. PART – C 17.5 Kg BAG
No Features & Benefits content added yet.
08976907887 
sales@mconrasayan.com 
